Airsoft GI small logo

Masamune Extreme Precision 6.01mm AEG Inner Barrel for M16A2/M14 (510mm)

[Z10G06B][06170 / D01-020]
$43.00
( 5 Reviews ) ❤ Add to Wishlist
OUT OF STOCK

Battery Information Video
New to airsoft? Here are some safety tips for airsoft guns that we recommend following.

The Airsoft GI Masamune 6.01mm Precision Barrel is the tightest bore barrel available and the only choice for players looking for the best possible accuracy and range.

Specifications:
Manufacturer: Masamune
Length: 510mm/20.08"
Bore: 6.01mm

Please Note:
The bore of this barrel is so tight around the BB that even the smallest obstruction in the barrel will cause a jam when fired. This barrel is recommended ONLY for advanced/experienced players that take the responsibility to clean their barrels regularly in order to avoid jams.

Airsoft GI recommends cleaning this barrel after every day of use.





Specifications
Manufacturer: Airsoft GI
Color: Silver
Size: 510mm
Material: Brass, Chrome Coated
Package Includes: One (1) Precision Inner Barrel
see 5 reviews | Write a Review
verified buyer
A. HOLZTRAGER | 2010-01-16
Product Information:
Well I have been airsofting for a while and I wrote a pretty detailed review about my KWA SR-10. I have listened to all the hype and watched the videos about these barrels. I would like to give my personal thanks to Airsoft GI for making these barrels available as a mass produced alternative for companies like DB Custom and PDI who are ripping customers off for barrels that dont COST anymore to make than 6.03 tightbores.

When these became available I quickly bought 2 of them even though I heard the rumors about the quality not being as good as should be. Today I installed the barrels in my KWA M16 and KWA SR-10. Due to problems with my KWA M16 that was not related to the barrels Im gonna skip to my SR-10. The stock barrel in the SR-10 is obvioulsy very good since its KWA and I did some shooting tests with it before and after replacing the barrel that I will not include in the review.

The ASGI 6.01 barrel greatly increased accuracy and FPS. I was confused at first when I was getting flyers with the new barrel (many more than before) but I believe it was because I was already shooting at the upper end of the FPS limit for .25s and the increase in FPS from the barrel made the BB to unstable. I then switched to .3s and had much better success with performance.

Great barrels, Great buy

Notice: The ONLY ammo I use in my guns are KSC .25s or KSC .3s made by KWA=best performance available

Pros:
-Increased Accuracy/Groupings
-Increased FPS
-PRICE

Cons:
-Increased FPS much more than I was expecting and will now only be able to shoot .3s (personal con)
verified buyer
C. LEWIS | 2010-03-08
Product Information:
The barrel I purchased was wildly shooting bbs to the right. Same issue as the guy below me. On careful inspection the window for the bucking was cut incorrectly and had a lip that was pushing the bucking over and causing the spin to be put on the bb incorrectly therefore forcing it right as it came out of the barrel.

The bad thing is, another person on my team order this same barrel and his does the EXACT SAME THING!!! Thats at least 3 barrels that I know of with the same issue! Before people go spouting out that we didn't test it right, we tested it in 3 different guns, all with bucking aligned correctly, and took the same 3 guns and tested with an EDGI barrel aligned in the same way. The ASGI barrel caused the right spin and the EDGI didn't....its the barrel, no question about it.

Contacted ASGI about this and they were less then helpful. Said they don't replace inner barrels. I am contacting them again about it and hopefully will receive a new one that is cut correctly, we'll see.

Pros:
- cheaper than EDGI or other barrels

Cons:
- BAD quality control, at least 3 barrels with bad cuts is just sad
- mutliple barrels with the same issue, and ASGI doesn't seem to want to do anything about it
verified buyer
W. BIELANOS | 2010-05-03
Product Information:
ok so i tested this in my g&g m14 with modify torque ups an amp high torque motor and an m150 spring also a green g&g hop up and an scs nub. The gun fired 530fps with .2s. Using this set up i recieved less than impressive results, even with .36g bbs. however, upon further research (internet, talking to another sniper at my local field) we discoverd that 6.01 mm barrels have problems holding target at such a high fps (his gun shoots 550fps on a .2 and he uses a db customs 6.01)the moral of the story is, if your going to buy a 6.01mm barrel use it in a gun that shoots below 450fps or your accuracy will suffer go with a 6.03

Pros:
-nice barrel
-increases your fps
-quality metal
-nice finsh (inside and out)

Cons:
hop up window looks like it was shodily cut
-bad gorupings with high fps (all 6.01s)
 
Will this work for ca sr-25
Will this work for a ca sr-25 if not could you recommend a 6.01 barrel that would

3446 days ago
Grant J
0
0

(I have this same question)
Staff Answer:
It should work

3445 days ago
0
0
1 answers
1 asked
 
would this inner barrel work in a kwa lm4
would this inner barrel work inside a kwa lm4 gbbr

3540 days ago
Roni B
0
0

(I have this same question)
Staff Answer:
No.

3539 days ago
0
0
1 answers
1 asked
Search Tags: Internal Upgrade Replacement Tightbore Range Accuracy Part Piece Increase Performance Trajectory Grouping Distance Output Tight Bore

For Questions, Answers and Comments:

Talk about the Masamune Extreme Precision 6.01mm AEG Inner Barrel for M16A2/M14 (510mm) with your friends on the facebook comments box below:
Copyright © 2024 Airsoft GI
Disclaimer:

All airsoft guns are required to have the tip (1/4 inch) of the barrel permanently colored in blaze orange. No person may openly display or expose any imitation firearm (replica firearm), in a public place. The term "public place" means an area open to the public or exposed to public view and includes streets, sidewalks, bridges, alleys, plazas, parks, driveways, parking lots, automobiles, whether moving or not, and buildings open to the general public, including those that serve food or drink, or provide entertainment, and the doorways and entrances to buildings or dwellings and the grounds enclosing them.

Any person who changes, alters, removes, or obliterates any coloration or markings that are required for by any applicable state or federal law or regulation, for any imitation firearm (replica firearm), or device in any way that makes the imitation firearm (replica firearm) or device look more like a firearm is guilty of violating the state or federal law.

By accessing the Site, you certify that you are older than 18 years of age or the age of majority where you live, whichever is older; that you are the owner of any credit card used to purchase on items on the Site; that you are familiar with all local laws in your area affecting your legal right to access airsoft products; that any products you buy are for your own private enjoyment and that you will NEVER share these products with a minor in ANY WAY.