Valken Energy 11.1v 1600mAh 3s 20C LiPO Battery
[K10A00][14734 / 48207]Free Shipping for orders over $179 No Coupon neededNew to airsoft? Here are some safety tips for airsoft guns that we recommend following.
Please Note: Lithium Polymer batteries MUST be charged with a Lithium Polymer Balance Charger!
Description:
Lithium Polymer batteries are the newest available batteries for airsoft and other hobby toys. They are designed as a light weight, high output power source. This 11.1v Li-Po battery can deliver more power than 12v Ni-MH large type battery with only half of the size and a third of the battery cells.
Specifications:
Manufacturer: Valken
Voltage: 11.1v
Milliampere Hours: 1600mAh
Cell Type: Lithium Polymer (LiPo)
Connector Type: Mini
Recommended Fit: M4A1, AK, M14, MP5, G36
LiPoSack Use and Safety Instructions:
Battery safety:
∑ Lithium Polymer batteries are volatile. Failure to adhere to established charging guidelines may result in fire, personal injury and damage to property if charged or used improperly.
- The makers of LipoSack or its distributors or retailers assume no liability for failures to comply with these use and safety guidelines.
- By purchasing this product, the buyer assumes all risks associated with its intended use. If you cannot comply with these guidelines please return this product unused to your retailer.
1) Charge batteries in a safe area away from flammable materials and only on a non-flammable surface in a vented area. Do not discharge batteries below 3 volts/cell. Doing so may result in cell damage and subsequent cell venting upon a subsequent charge.
2) Do not recharge damaged batteries. Dispose of damaged batteries in the proper manner.
3) Some Lipo chargers on the market may have technical deficiencies that may cause it to charge the battery incorrectly or at an improper rate. It is your sole responsibility to assure that the charger you purchased works properly. Always monitor the charging process to assure batteries are being charged properly. Failure to do so may result in cell damage or fire.
4) In the event of a crash, you must remove the battery from the model for observation and place in a safe open area away from flammable materials.
LipoSack Use Instructions:
1) Ensure that charger rate is properly set and polarity is correct.
2) Attach charging leads to battery.
3) Place battery in LipoSack towards the bottom.
4) Place LipoSack on non-flammable surface.
5) Route charge leads through vent at the top seam of the LipoSack.
6) Close top flap of LipoSack and press hook and loop closure fully closed.
7) Charge battery using proper charging practices.
Airsoft GI Battery Disclaimer:
Airsoft GI is not responsible for batteries that have been damaged as a result of improper operation, storage, misuse or abuse, accident or neglect, such as physical damage resulting from misuse; contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; use of the battery for commercial purposes or subjecting the battery to abnormal usage conditions, or other acts which are not the fault of Airsoft GI. Make sure you understand how your battery should be used and how long it should be charged. If you have any doubt regarding the operation, charging, or storage of your battery and/or charger, ask. A charging battery should not be left unattended and should be picked up periodically while charging to check for overheating. Do not charge batteries near flammable material. For more information regarding batteries please refer to the Frequently Asked Questions or the Airsoft GI Airsoft 101 Guide.
- Specifications
- Manufacturer: Valken
|
compatibility
Will this fit in a Lancer Tactical M4
2076 days ago Spongy S
0
0
(I have this same question)
Staff Answer:
This battery is very large and will require a stock with a large cavity to store. This will not fit into a standard crane style stock. 2064 days ago 0
0
|
1 answers 1 asked |
|
Will it fit?
Will it fit in a kytac crb mk2 stock?
2122 days ago Randy Y
0
0
(I have this same question)
Staff Answer:
They will not fit in the CRB stock. 2122 days ago 0
0
|
1 answers 1 asked |
|
Classic Army ECR 5 M4 Crane stock
Will these batteries fit in the above mentioned rifle/stock?
2514 days ago Noah W
0
0
(I have this same question)
Staff Answer:
They will not, the cells are too large 2119 days ago 0
0
|
1 answers 1 asked |
|
small tamya
would it work with a small tamya connector
in my G&G combat machine
2833 days ago dave j
0
0
(I have this same question)
Staff Answer:
It will connect but it may not fit 2833 days ago 0
0
|
1 answers 1 asked |
|
Compatibility
Would this fit in a Ares Amoeba M4 Carbine
3226 days ago Andrew S
0
0
(I have this same question)
Staff Answer:
No. 3171 days ago 0
0
|
1 answers 1 asked |
|
PEQ Box
will this fit any PEQ Box? or what battery will?
3275 days ago Noah K
0
0
(I have this same question)
Staff Answer:
It should fit in a PEQ-2 style 3274 days ago 0
0
|
1 answers 1 asked |
|
Peq
What peq box will this fit in? If none, how should I house this in a 13" vtac rail?
3276 days ago Michael A
0
0
(I have this same question)
Staff Answer:
This battery will fit in: <BR><BR> <a href="http://www.airsoftgi.com/product_info.php?products_id=12497">D Boy PEQ Battery box [Link]</a> 3268 days ago 0
0
|
1 answers 1 asked |
|
Scar
Will this battery fit a vfc scar-l?
3300 days ago brian y
0
0
(I have this same question)
Staff Answer:
Yes, there should be adequate space within the stock for this battery. 3298 days ago 0
0
|
1 answers 1 asked |
|
does it fit in the handgaurd of a g&g gk99 | 0 answers 1 asked |
|
will it fit?
will it fit in a kwa g36c?
3522 days ago David C
0
0
(I have this same question)
Staff Answer:
It will not 3521 days ago 0
0
|
1 answers 1 asked |
|
Magpul PDR
Would this fit into a Magpul PDR well?
3597 days ago Scott M
0
0
(I have this same question)
Staff Answer:
No it will not fit 3597 days ago 0
0
|
1 answers 1 asked |
|
Will this Fit in a Magpul Masada?
Will this Fit in a Magpul Masada?
3682 days ago Kevin L
0
0
(I have this same question)
Staff Answer:
This should fit okay. 3682 days ago 0
0
|
1 answers 1 asked |
|
crane stock fit?
will this tri panel battery fit a crane stock?
3698 days ago lukas l
0
0
(I have this same question)
Staff Answer:
This battery won't fit crane stocks very well. This one might be a better choice for crane stocks: http://www.airsoftgi.com/product_info.php?products_id=11916 3696 days ago 0
0
|
1 answers 1 asked |
Other Great Deals and Accessories:
Select the item from the Drop Down Menu and click add.