Airsoft GI small logo

Tenergy LiPo 11.1v 1000mAh 3s 20C Stick Battery

[K15D00][11914 / 31598]
$22.48
( 3 Reviews ) ❤ Add to Wishlist
OUT OF STOCK
Orders over $179 qualify for free shipping
Free Shipping for orders over $179 No Coupon needed
New to airsoft? Here are some safety tips for airsoft guns that we recommend following.

Please Note: Lithium Polymer batteries MUST be charged with a Lithium Polymer Balance Charger!

Lithium Polymer batteries are the newest available batteries for airsoft and other hobby toys. They are designed as a light weight, high output power source. This 11.1v Li-Po battery can deliver more power than 12v Ni-MH large type battery with only half of the size and a third of the battery cells.

While Tenergy batteries are great, I Power LiPO batteries are now available with more mAh for an affordable price! Check out I Power LiPO batteries by click HERE.

Specifications:
Manufacturer: Tenergy
Voltage: 11.1v
Milliampere Hours: 1000mAh
Cell Type: Lithium Polymer (LiPo)
Connector Type: Mini
Recommended Fit: M4A1, AK, M14, MP5, G36

    LiPoSack Use and Safety Instructions:
    Battery safety:

    ∑ Lithium Polymer batteries are volatile. Failure to adhere to established charging guidelines may result in fire, personal injury and damage to property if charged or used improperly.

  • The makers of LipoSack or its distributors or retailers assume no liability for failures to comply with these use and safety guidelines.
  • By purchasing this product, the buyer assumes all risks associated with its intended use. If you cannot comply with these guidelines please return this product unused to your retailer.


    1) Charge batteries in a safe area away from flammable materials and only on a non-flammable surface in a vented area. Do not discharge batteries below 3 volts/cell. Doing so may result in cell damage and subsequent cell venting upon a subsequent charge.
    2) Do not recharge damaged batteries. Dispose of damaged batteries in the proper manner.
    3) Some Lipo chargers on the market may have technical deficiencies that may cause it to charge the battery incorrectly or at an improper rate. It is your sole responsibility to assure that the charger you purchased works properly. Always monitor the charging process to assure batteries are being charged properly. Failure to do so may result in cell damage or fire.
    4) In the event of a crash, you must remove the battery from the model for observation and place in a safe open area away from flammable materials.

    LipoSack Use Instructions:

    1) Ensure that charger rate is properly set and polarity is correct.
    2) Attach charging leads to battery.
    3) Place battery in LipoSack towards the bottom.
    4) Place LipoSack on non-flammable surface.
    5) Route charge leads through vent at the top seam of the LipoSack.
    6) Close top flap of LipoSack and press hook and loop closure fully closed.
    7) Charge battery using proper charging practices.

Airsoft GI Battery Disclaimer:
Airsoft GI is not responsible for batteries that have been damaged as a result of improper operation, storage, misuse or abuse, accident or neglect, such as physical damage resulting from misuse; contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; use of the battery for commercial purposes or subjecting the battery to abnormal usage conditions, or other acts which are not the fault of Airsoft GI. Make sure you understand how your battery should be used and how long it should be charged. If you have any doubt regarding the operation, charging, or storage of your battery and/or charger, ask. A charging battery should not be left unattended and should be picked up periodically while charging to check for overheating. Do not charge batteries near flammable material. For more information regarding batteries please refer to the Frequently Asked Questions or the Airsoft GI Airsoft 101 Guide.

Specifications
Manufacturer: Tenergy
see 3 reviews | Write a Review
B. JACOBSEN | 2014-03-26
Product Information:
I got two of theses and one worked amazingly and almost lasts all day but the outher seemed to be defective and only lasts about 15 minutes

Pros:
Raised my rof to 21 with the stock motor, and has a good duration

Cons:
On of the ones I got was defective
M. RYAN | 2014-06-09
Product Information:
I have this battery for about 2 months and it works fantastic. If you are a looking for a good 11.1 lipo battery i highly recomend it for you.

Pros:
nice rate of fire
small enough to fit in handguards and buffer tubes
its just awesome

Cons:
It is a lipo battery and kind of dangerous but its whatever. (worth it)
verified buyer
R. VOLLMER | 2018-05-05
Product Information:
I use these batteries almost exclusively. They are absolutely excellent. Solid rate of fire.

I have had only one fail, and that was after 2+ years of use.

Pros:
Provides excellent rate of fire (have used this battery with KWA M16 and Krytac CRB MkII)
Reliable

Cons:
There are no cons to speak of. For the price you get an effective and reliable batter.
 
Classic army nemesis series with the PDR stock?
Will it fit?

2247 days ago
Jacob D
0
0

(I have this same question)
Staff Answer:
It will fit, but you need to rewire the battery to deans. I recommend grabbing the tube extension for the nemesis. http://www.airsoftgitv.com/quick-tip-installing-battery-classic-army-nemesis-guns/

2176 days ago
0
0
1 answers
1 asked
 
Can you provide Dimensions?
I would like, for all of us, a possible list of Dimensions for the batteries on your guy's website. You are probably the most trusted people out there for airsoft guns, and if you were able to provide dimensions for all of the batteries on the website all of these "Will it fit?" questions could be solved by a simple ruler at home and no further hassle. Thank you so much!

2252 days ago
Daniil B
0
0

(I have this same question)
Staff Answer:
the dimensions for this battery are: 16mmx20mmx102mm each size of battery is slightly different, so it is always important to check in person if possible

2176 days ago
0
0
1 answers
1 asked
 
Will this fit in an ASG cz 805 Bren?
Battery space is very limited.

2654 days ago
Brian J
0
0

(I have this same question)
Staff Answer:
Yes it will.

2163 days ago
0
0
1 answers
1 asked
 
Will this fit the 805 Bren
Will this battery fit in the ASG CZ 805 Bren?

2660 days ago
Brian J
0
0

(I have this same question)
Staff Answer:
Yes it will.

2163 days ago
0
0
1 answers
1 asked
 
will the 11.1 lipo fit in a mil spec buffer tube?
Will the 11.1 lipo fit in a mil spec buffer tube

3230 days ago
austin e
0
0

(I have this same question)
Staff Answer:
Yes.. It should be able to.

3176 days ago
0
0
1 answers
1 asked
 
FMG4
Will this work fine in my fmg4 with the superkong 2 MOSFET or will I need more upgrades

3242 days ago
darius l
0
0

(I have this same question)
Staff Answer:
Yes

3241 days ago
0
0
1 answers
1 asked
 
Will this fit a Amoeba CCP?
I have an upgraded CCP and wondered if it would fit the top rail of it.

3265 days ago
Kyle C
0
0

(I have this same question)
Staff Answer:
It will not fit inside. It will scrape the side of the battery. A 7.4v LiPo is optimal.

3245 days ago
1
0
1 answers
1 asked
 
does it have a small tamiya connector
for stoner lmg

3272 days ago
matthew L
0
0

(I have this same question)
Staff Answer:
Yes, this battery uses a small type Tamiya connector.

3270 days ago
0
0
1 answers
1 asked
 
Will this fit ak dust cover
Is this battery small enough to properly fit ak dust cover

3282 days ago
Rick W
0
0

(I have this same question)
Staff Answer:
Depending on the brand of AK, there may be enough space. However, the fitment may be very tight with various brands.

3281 days ago
0
0
1 answers
1 asked
 
Wiring
Is this battery wired to deans for a deans connector

3302 days ago
Cole B
0
0

(I have this same question)
Staff Answer:
No

3298 days ago
0
0
1 answers
1 asked
 
Would this battery fit inside of an ICS SG552?
Would this battery fit into the handguard of this gun.

3326 days ago
Drew W
0
0

(I have this same question)
Staff Answer:
It should

3326 days ago
0
0
1 answers
1 asked
 
Will this fit in a KWA KM4 Commando?
Will this fit in said gun? Also, will it fit WITHOUT voiding the warranty?

3326 days ago
Ray S
0
0

(I have this same question)
Staff Answer:
It will fit, but it will void the warranty

3326 days ago
0
0
1 answers
1 asked
 
Will this fit in my KWA M4 CQR Mod 2?
Will it fit without modifying the gun?

3329 days ago
Ray S
0
0

(I have this same question)
Staff Answer:
It should fit

3329 days ago
0
0
1 answers
1 asked
 
Will this fit a g&g firehawk
Will this battery fit inside of the buffer tube of my g&g firehawk

3343 days ago
Anthony T
0
0

(I have this same question)
Staff Answer:
It should

3338 days ago
0
0
1 answers
1 asked
 
Will this fit a g&g firehawk
Will this battery in the stock of my g&g firehawk

3344 days ago
Anthony T
0
0

(I have this same question)
Staff Answer:
It should

3338 days ago
0
0
1 answers
1 asked
 
Explanation
I just got this battery about two weeks ago. I charged it up and used it then left it in their over a couple of days I dont know if that was a bad decison but I took it out and put it back in and started firing again and was working perfectly still. I then removed it once I knew the battery had know more life in it and starte charging it up again. For some reason It will not charge no matter what. It says on my lipo charger it is charging and then it switches to a current drip which means it ahould be nearly fully cheged already. But it woll not fire no matter what just wondering if anyone had a suggestion

3350 days ago
jack r
0
0

(I have this same question)
Staff Answer:
Please contact our customer service for assistance.

3347 days ago
0
0
1 answers
1 asked
 
Will this fit a lancer tactical 0 answers
1 asked
 
will it fit?
will it fit in a buffer tube and/or APS UAR Urban Assault Rifle?

3393 days ago
Louie G
0
0

(I have this same question)
Staff Answer:
Buffer tube yes, APS UAR no

3375 days ago
0
0
1 answers
1 asked
 
battery compartment
Will this fit in a e&l AK wired to the top, and is it recommended

3420 days ago
Ian P
0
0

(I have this same question)
Staff Answer:
You will need the tri panel style

3416 days ago
0
0
1 answers
1 asked
 
Will this battery fit in the krytac crb?
I am hoping to get the krytac crb soon and will be needing a battery and was thinking of this one, will it fit either in the buffer tube or vertically?

3473 days ago
Tim G
0
0

(I have this same question)
Staff Answer:
Yes it will fit

3472 days ago
0
0
1 answers
1 asked
 
Battery Life
How long would this battery last on the field, considering that it's only 1000mAh

3515 days ago
Rudy J
0
0

(I have this same question)
Staff Answer:
There are too many factors to accurately tell how long it will last.

3514 days ago
0
0
1 answers
1 asked
 
Fit
Will this fit a PEQ box with dimensions of 64mmX51mmX16mm

3531 days ago
Eli H
0
0

(I have this same question)
Staff Answer:
No

3529 days ago
0
0
1 answers
1 asked
 
Use
Will this battery void the warranty of a VFC IAR and is it recommended?

3536 days ago
Martin P
0
0

(I have this same question)
Staff Answer:
Yes it will void the warranty period.

3535 days ago
0
0
1 answers
1 asked
 
Will this fit in a KWA G36c
Couldn't find any battery dimensions otherwise I wouldn't be asking.

3536 days ago
Max D
0
0

(I have this same question)
Staff Answer:
Yes it should fit.

3536 days ago
0
0
1 answers
1 asked
 
Connector type
Will this connect with a small tamiya connector

3563 days ago
Bryce M
0
0

(I have this same question)
Staff Answer:
This is a small type connector

3563 days ago
0
0
1 answers
1 asked
 
Will this battery fit in a KM4 SR7
Will it fit in the crane stock of the KM4 SR7

3569 days ago
Dylan G
0
0

(I have this same question)
Staff Answer:
It should, however it will void the warranty of the gun

3569 days ago
0
0
1 answers
1 asked
 
fit
Will this fit in a madbull Lipo buffer tube

3574 days ago
Will S
0
0

(I have this same question)
Staff Answer:
It should be able to fit

3574 days ago
0
0
1 answers
1 asked
 
Hk 416
Will this fit into the buffer tube of the hk 416?

3579 days ago
Langston T
0
0

(I have this same question)
Staff Answer:
It should be able to fit into a buffer tube

3578 days ago
0
0
1 answers
1 asked
 
Will it fit in the G&G F2000
I want to know so I can have a powerful battery for my gun.

3580 days ago
Martin P
0
0

(I have this same question)
Staff Answer:
It should work, however this battery is not recommended

3578 days ago
0
0
1 answers
1 asked
 
Fit in an Echo 1 Red Star LMG?
Title

3583 days ago
Austin C
0
0

(I have this same question)
Staff Answer:
It should be able to fit, however we recommend either a 9.6v NiMH battery or a 7.4 LiPo battery

3582 days ago
0
0
1 answers
1 asked
 
WOOOOOO! ak700? WOOOOOOOO! 0 answers
1 asked
 
Life! 0 answers
1 asked
 
Will this fit in my KWA M4 A1 CQR MOD 1
I want to know so it fits my gun.

3611 days ago
Michael N
0
0

(I have this same question)
Staff Answer:
It will fit, however it is not recommend. We recommend either a 9.6v Nunchuck or a 7.4 LiPo

3611 days ago
0
0
1 answers
1 asked
 
Does it fit a A&K Magpul Masada?
I was wondering if it fit....

3622 days ago
Benjamin Z
0
0

(I have this same question)
Staff Answer:
It may fit, however a 9.6v nunchuck is recommended over an 11.1.

3620 days ago
0
0
1 answers
1 asked
 
C rating
What is the burst C rating on these lipos? I can see the constant but there is no burst.

3639 days ago
Trey W
0
0

(I have this same question)
Staff Answer:
It is unlisted on the packaging.

3639 days ago
0
0
1 answers
1 asked
 
Can I put this in a buffer tube?
Can I put this in an A&K cqb m4 buffer tube?

3647 days ago
Ramon C
0
0

(I have this same question)
Staff Answer:
This battery should be able to fit into most buffer tubes.

3647 days ago
0
0
1 answers
1 asked
 
will this Fit my Full metal JG M4 Stubby Killer CqB?
Want to know before i purchase this?

3648 days ago
Jake B
0
0

(I have this same question)
Staff Answer:
It should fit.

3648 days ago
0
0
1 answers
1 asked
 
Will this battery fit in a JG Full Metal M4 Stubby Killer AEG Airsoft Gun
I want to know before i purchase this product

3648 days ago
Jake B
0
0

(I have this same question)
Staff Answer:
It should fit.

3648 days ago
0
0
1 answers
1 asked
 
VFC 417
Would my VFC 417 be ok running on this 11.1 lipo?

3660 days ago
Noah R
0
0

(I have this same question)
Staff Answer:
We recommend either using a 9.6v NiMH battery or a 7.4 LiPo battery.

3660 days ago
0
0
1 answers
1 asked
 
will this work inthe kwa cqr mod 2
Don't know what kind of battery to buy for it please answer

3669 days ago
alex p
0
0

(I have this same question)
Staff Answer:
This should work. Please keep in mind that Airsoft GI recommends a 7.4v Li-Po or 9.6V NiMH battery.

3668 days ago
0
0
1 answers
2 asked
 
can i fit this in a peq box?
will this battery fit inside of a peq box? the peq box can hold a battery with the dimensions of 70mmx45mmx20mm.

3686 days ago
Dan T
0
0

(I have this same question)
Staff Answer:
This product will not fit in that PEQ box.

3683 days ago
0
0
1 answers
1 asked
 
can this fit a crane stock???? 0 answers
6 asked
 
Is this a good battery for a KWA Full Metal M4 Troy
I am trying to find out if I should order this Tenergy 11.1 1000mah 20c stick lipo for a KWA M4 TROY AEG, and I hope next month ill have the KWA SR10 and it will fit this gun to, please help, thanks!

3698 days ago
MITCHELL D
0
0

(I have this same question)
Staff Answer:
This battery should work okay in a KWA.

3696 days ago
0
0
1 answers
1 asked
 
Will this battery fit in a crane stock?
I am going to purchase this battery and I am wondering if this will fit in a crane stock. If not, do you have any suggestions on an 11.1 lipo that will fit. Thank you.

3698 days ago
Cody S
0
0

(I have this same question)
Staff Answer:
This battery should fit fine in a crane stock.

3696 days ago
0
0
1 answers
2 asked

Other Great Deals and Accessories:
Select the item from the Drop Down Menu and click add.

Charger
 
Gear Accessories
 
LIPO Battery Safety information image

Search Tags: Lithium Polymer 2 Cell M4 KWA MK36 G36 AEG AK S MK5K 11.1 1000 LiPo Lithium Polymer Phosphate PO4 Li ion Fe Iron

For Questions, Answers and Comments:

Talk about the Tenergy LiPo 11.1v 1000mAh 3s 20C Stick Battery with your friends on the facebook comments box below:
Copyright © 2024 Airsoft GI
Disclaimer:

All airsoft guns are required to have the tip (1/4 inch) of the barrel permanently colored in blaze orange. No person may openly display or expose any imitation firearm (replica firearm), in a public place. The term "public place" means an area open to the public or exposed to public view and includes streets, sidewalks, bridges, alleys, plazas, parks, driveways, parking lots, automobiles, whether moving or not, and buildings open to the general public, including those that serve food or drink, or provide entertainment, and the doorways and entrances to buildings or dwellings and the grounds enclosing them.

Any person who changes, alters, removes, or obliterates any coloration or markings that are required for by any applicable state or federal law or regulation, for any imitation firearm (replica firearm), or device in any way that makes the imitation firearm (replica firearm) or device look more like a firearm is guilty of violating the state or federal law.

By accessing the Site, you certify that you are older than 18 years of age or the age of majority where you live, whichever is older; that you are the owner of any credit card used to purchase on items on the Site; that you are familiar with all local laws in your area affecting your legal right to access airsoft products; that any products you buy are for your own private enjoyment and that you will NEVER share these products with a minor in ANY WAY.