Tenergy LiPo 7.4v 1000mAh 2s 20C Butterfly Pack Battery
[SF11][11915 / 31599 / LIPO7.4V1000N]Free Shipping for orders over $179 No Coupon neededNew to airsoft? Here are some safety tips for airsoft guns that we recommend following.
Please Note: Lithium Polymer batteries MUST be charged with a Lithium Polymer Balance Charger!
Lithium Polymer batteries are the newest available batteries for airsoft and other hobby toys. They are designed as a light weight, high output power source. This 7.4v Li-Po battery can deliver more power than 9.6v Ni-MH large type battery with only half of the size and a third of the battery cells.
While Tenergy batteries are great, I Power LiPO batteries are now available with more mAh for an affordable price! Check out I Power LiPO batteries by click HERE.
Specifications:
Manufacturer: Tenergy
Voltage: 7.4v
Milliampere Hours: 1000mAh
Cell Type: Lithium Polymer (LiPo)
Connector Type: Mini
Recommended Fit: M4A1, AK, M14, MP5, G36
- The makers of LipoSack or its distributors or retailers assume no liability for failures to comply with these use and safety guidelines.
- By purchasing this product, the buyer assumes all risks associated with its intended use. If you cannot comply with these guidelines please return this product unused to your retailer.
1) Charge batteries in a safe area away from flammable materials and only on a non-flammable surface in a vented area. Do not discharge batteries below 3 volts/cell. Doing so may result in cell damage and subsequent cell venting upon a subsequent charge.
2) Do not recharge damaged batteries. Dispose of damaged batteries in the proper manner.
3) Some Lipo chargers on the market may have technical deficiencies that may cause it to charge the battery incorrectly or at an improper rate. It is your sole responsibility to assure that the charger you purchased works properly. Always monitor the charging process to assure batteries are being charged properly. Failure to do so may result in cell damage or fire.
4) In the event of a crash, you must remove the battery from the model for observation and place in a safe open area away from flammable materials.
LipoSack Use Instructions:
1) Ensure that charger rate is properly set and polarity is correct.
2) Attach charging leads to battery.
3) Place battery in LipoSack towards the bottom.
4) Place LipoSack on non-flammable surface.
5) Route charge leads through vent at the top seam of the LipoSack.
6) Close top flap of LipoSack and press hook and loop closure fully closed.
7) Charge battery using proper charging practices.
LiPoSack Use and Safety Instructions:
Battery safety:
∑ Lithium Polymer batteries are volatile. Failure to adhere to established charging guidelines may result in fire, personal injury and damage to property if charged or used improperly.
Airsoft GI Battery Disclaimer:
Airsoft GI is not responsible for batteries that have been damaged as a result of improper operation, storage, misuse or abuse, accident or neglect, such as physical damage resulting from misuse; contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; use of the battery for commercial purposes or subjecting the battery to abnormal usage conditions, or other acts which are not the fault of Airsoft GI. Make sure you understand how your battery should be used and how long it should be charged. If you have any doubt regarding the operation, charging, or storage of your battery and/or charger, ask. A charging battery should not be left unattended and should be picked up periodically while charging to check for overheating. Do not charge batteries near flammable material. For more information regarding batteries please refer to the Frequently Asked Questions or the Airsoft GI Airsoft 101 Guide.
- Specifications
- Manufacturer: Tenergy
It's a great product definitely worth the 16.00!! Just remember to use a good charger!
Pros:
Cons:
|
Connector and stock fit
what kind of connector does this come with and would it fit in my M8A3 Stag-15 crane stock? and would I need a new connector?
3268 days ago Luke S
0
0
(I have this same question)
Staff Answer:
This will fit in your airsoft gun and they both have small tamiya connectors. 3266 days ago 0
0
|
1 answers 1 asked |
|
Is there a connector or just wires?
this is a bad picture i cant tell
3327 days ago Joshua H
0
0
(I have this same question)
Staff Answer:
It has small type connectors 3326 days ago 0
0
|
1 answers 1 asked |
|
will it fit elite force h&k G36C | 0 answers 1 asked |
|
could this fit in an E&L AK
I know that the e&l aks are meant for stick type batteries but if this could still fit
3454 days ago Ian P
0
0
(I have this same question)
Staff Answer:
It may be able to fit with skillful maneuvering 3453 days ago 0
0
|
1 answers 1 asked |
|
will this fit my King Arms Full Metal Smith & Wesson M&P15 MOE Carbine
im buying a new battery would this fit well ?
3454 days ago Alec C
0
0
(I have this same question)
Staff Answer:
Yes it should 3447 days ago 0
0
|
1 answers 1 asked |
|
Gi Custom?
I am new to lipos do you think it would be to powerfull to use in a stock Airsoft GI G4-A2 Sapper do you think it will last at least 2 years using this lipo and will this fit in the crane stock
3530 days ago Brenda P
0
0
(I have this same question)
Staff Answer:
It should be fine 3529 days ago 0
0
|
1 answers 1 asked |
|
would this fit in my ics sig 552 handguard
i am wondering if this would fit in my ics sig 552 handguard.
3533 days ago jadden T
0
0
(I have this same question)
Staff Answer:
It should 3531 days ago 0
0
|
1 answers 1 asked |
|
fit in a G4 Dune Knight?
I have a G4A5 Dune Knight. Will this fit in the crane stock?
3540 days ago Dean S
0
0
(I have this same question)
Staff Answer:
It should 3539 days ago 0
0
|
1 answers 1 asked |
|
ef m27 iar
Will this fit in the elite force m27 iar by vfc crane stock
3552 days ago Chase R
0
0
(I have this same question)
Staff Answer:
it should fit 3551 days ago 0
0
|
1 answers 1 asked |
|
elite force m4 cqb
Will this fit in the crane stock of the elite force m4 cqb?
3588 days ago Gabriel C
0
0
(I have this same question)
Staff Answer:
It should fit 3587 days ago 0
0
|
1 answers 1 asked |
|
small type connector
Will this fit a small type battery connector
3592 days ago Gabriel C
0
0
(I have this same question)
Staff Answer:
Yes, this has a small type connector 3591 days ago 0
0
|
1 answers 1 asked |
|
Tamiya or deans
What type of connectors does this use deans or tamiya? If tamiya large or small type?
3600 days ago Pamela C
0
0
(I have this same question)
Staff Answer:
It should have Tamiya connectors 3599 days ago 0
0
|
1 answers 1 asked |
|
Will this work in a Crane stock ?
Will this work? Or would a stick type lipo be better in the buffer tube?
3676 days ago Chris D
0
0
(I have this same question)
Staff Answer:
This should fit in a crane stock. 3676 days ago 0
0
|
1 answers 1 asked |
|
9.6 or 7.4?
First off, will this fit into the g&g gr15? Second does a 7.4 lipo give a higher rof than a 9.6? Or vise versa?
3688 days ago Brian R
0
0
(I have this same question)
Staff Answer:
This should fit. The 7.4V Lipo should give the same ROF as a 9.6V. 3685 days ago 0
0
|
1 answers 1 asked |
|
What lipo charger do it get for a 7.4?
charger!
3735 days ago Elvis P
0
0
(I have this same question)
Staff Answer:
You'll need a Li-Po Balance Charger: http://www.airsoftgi.com/product_info.php?products_id=7786 3735 days ago 0
0
|
1 answers 1 asked |
Other Great Deals and Accessories:
Select the item from the Drop Down Menu and click add.